![]() ![]() You can also tap the effect name, then tap Disable at the top of the inspector. (To enable the effect, swipe left, then tap. Temporarily disable the Green Screen Keyer: Swipe left over its name, then tap. Tap Inspect in the lower-left corner of the screen, then tap at the top of the inspector.ĭelete the Green Screen Keyer: Swipe left over its name, then tap. You can animate some of these settings using keyframes, to compensate for changing conditions in the foreground clip. The default setting is 1, which results in the background fully replacing the green or blue screen. Mix: Drag the slider to set how much of the background clip is used to replace the green or blue screen. Use this control to simulate environmental lighting from the background being cast onto the foreground subject. Light Wrap: Drag the dial to increase or decrease the amount of color and brightness from the background that’s blended with the foreground subject. You can also tap the number field above the slider, then use the keypad to change the value. Drag to the left (decreasing the percentage value) to soften the edges of the key, or to the right (increasing the percentage value) to sharpen the edges. Luma Rolloff: Drag the slider to modify the range of brightness and darkness used to calculate the edges of the key. Invert Keyed Area: Turn on this setting to swap which area of the foreground is keyed (making the green or blue screen visible and the subject invisible).Ĭhroma Rolloff: Drag the slider to modify the range of hue and saturation used to calculate the edges of the key. (By default, Final Cut Pro applies spill removal, but you can further adjust it using this control.) Drag the slider right to make translucent regions more solid while expanding the key.Ĭolor Spill: Drag the slider to suppress any of the green or blue background color reflecting (or spilling) onto the foreground subject. Drag the slider left to make translucent regions more translucent while simultaneously shrinking the key. Shrink/Expand: Use this slider to adjust the contrast of the key to affect key translucence and key size simultaneously. This control is useful when you’re satisfied with the edges of your key, but you have unwanted holes in the interior that you can’t eliminate using the Strength control (without ruining your edges). The Strength control is useful for retrieving areas of semitransparent detail such as hair, smoke, or reflections.įill Holes: Drag the slider to the right to add solidity to regions of marginal transparency within a keyed subject. Increasing the value expands the range of color sampled, resulting in more transparency in the keyed image. Reducing this value narrows the range of color sampled, resulting in less transparency in the keyed image. Strength: Drag the dial to adjust the tolerance (core transparency) of the Green Screen Keyer’s automatic sampling. Tap Inspect in the lower-left corner of the screen, tap at the top of the inspector, then tap Green Screen Keyer. In the timeline, tap the foreground clip (the clip with the Green Screen Keyer applied), then drag the playhead over the clip (to see the result of your adjustments in the viewer). To fine-tune the effect, see the next task.Īfter you apply the Green Screen Keyer, you can fine-tune the effect in the inspector. In the viewer, the green or blue background is made transparent, and the background clip is visible through the areas of transparency. In the inspector, tap, tap, tap Masks and Keying, then tap Green Screen Keyer. In the browser, tap the Green Screen Keyer thumbnail, then tap Apply under the browser. Tap in the toolbar, tap Effects in the browser, then tap Video (if it’s not already selected).įrom the browser, drag the Green Screen Keyer thumbnail over the foreground clip in the timeline, and when the clip becomes highlighted, release your finger. In the timeline, drag the playhead over the two clips (to see the result of the keyer effect in the viewer), then tap the foreground clip. The foreground clip is connected to the background clip. Tap in the toolbar, then drag a clip to use as the background image from the browser to the primary storyline in the timeline.ĭrag the clip to use as the foreground image (the clip with the green-screen or blue-screen backdrop) from the browser to the timeline, to a position above the background clip. In Final Cut Pro for iPad, open a project. Create areas of transparency with masks.Use the Flow transition to merge jump cuts.Adjust depth of field in Cinematic mode clips. ![]() Adjust the focus in Cinematic mode clips.Change the focus in Cinematic mode video.Start a Final Cut Pro for iPad subscription. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |